Recent Posts

61

Tubular Motors: General Discussion / Re: Troubleshooting beeping motors

« Last post by freightguy on February 25, 2017, 01:16:40 PM »

I just installed a new motor into my shade all it does is give 1 beep when I push the power button.  What happened with your beeping issue?

62

Choosing a home automation system / Re: Changing the default "trigger on" period for the z-way relay

« Last post by StuartW on January 29, 2017, 08:35:18 PM »

Okay, just read that part again. I am actually using SmartThings but I figured it out. There is a parameter being passed in the z-wave command, within the Device Handler. Problem solved!

For anyone who is interested I created a virtual switch that I am using so I can trigger the preset/midpoint from Alexa, via the "stop" command. With the default at 1s it work most of the time. Setting it to 1.5s it works all the time.

63

Choosing a home automation system / Re: Changing the default "trigger on" period for the z-way relay

« Last post by admin on January 27, 2017, 05:53:48 PM »

Hello, did you see the instructions that show how to do that in the Vera interface?

Regards, Adrian

64

Choosing a home automation system / Changing the default "trigger on" period for the z-way relay

« Last post by StuartW on January 27, 2017, 04:47:31 PM »

In the z-wave relay  instructions it advises that it is possible to change the default "trigger-on" period which is set to 1s.

Can you provide the instructions to do this?

65

Tubular Motors: General Discussion / Re: Routing wires when soldering wires to 2-ch wireless wall switch

« Last post by lacoleman on December 13, 2016, 04:46:42 AM »

OK, then I've got it.  Thanks.

66

Tubular Motors: General Discussion / Re: Routing wires when soldering wires to 2-ch wireless wall switch

« Last post by admin on December 12, 2016, 10:09:31 PM »

Hi @lacoleman, there is no preferred route, it's just a matter of routing so you can still close the housing properly and not interfere with the operation.

Regards, Adrian

67

Tubular Motors: General Discussion / Routing wires when soldering wires to 2-ch wireless wall switch

« Last post by lacoleman on December 12, 2016, 05:36:41 PM »

I am wiring a 2-ch DCC-2W-RF wall switch using the wiring bundle from a DCC-ZWAVE-12R motor controller, connecting the wires to the pushbutton switches on the CB.  My question is whether there is a normal, preferred routing for the wires through the back of the wall switch unit.  I can see three possible routes but would rather follow the lead of someone who is has done this or is otherwise familiar with the usual practice.  Thanks.

68

Tubular Motors: General Discussion / Re: Setting one motor limit without changing the other limit

« Last post by lacoleman on December 12, 2016, 05:05:35 PM »

Hi @lacoleman, thanks for your feedback, that is good to know. I think you may be using our older series R motors; our newer G series have a finer jog function.

Regards, Adrian

You are right.  I am using the R-series.

69

Tubular Motors: General Discussion / Re: Customer Service In Motor Selection

« Last post by admin on December 08, 2016, 11:43:05 AM »

Hi All, aw shucks, youse are too kind! Nice to know our customer care is appreciated though!

Cheers, Adrian

70

Tubular Motors: General Discussion / Re: Setting one motor limit without changing the other limit

« Last post by admin on December 08, 2016, 11:39:05 AM »

Hi @lacoleman, thanks for your feedback, that is good to know. I think you may be using our older series R motors; our newer G series have a finer jog function.

Regards, Adrian